Topwell Machining Centres TW24L and TWL18

Questions ?
Call us at 905-624-5536.

H.H. Roberts Machinery Limited
1324 Matheson Blvd E., Mississauga, Ontario, Canada. L4W-2Z7, Fax 905-624-9065

The New HH Roberts / Topwell High Speed Mini-Mills are here !

Back to page 1 of the TWL introduction.

Topwell TW-18L high speed machining center

The TW-18L shown with optional spindle temperature control system at the right rear of the machine, for the 12,000 rpm spindle fitted on this one. The high speed spindles enable improved surface finish when using the high speed machining capabilities of the Anilam 6000i series CNC control.
Feed rates of 400 IPM or more are available in contouring with efficient programming. A 128 block look ahead and responsive European AC digital drives adapt to the contouring for blend contours smoothly.
This control is a hybrid of a Heidenhain CNC processor and servo drive system, combined with servo motors made in Europe at factories in the Heidenhain group of companies, AND the popular Anilam user interface for intuitive, flexible operation.

The Heidenhain Group owns Anilam.

Specifications are at the bottom of this page.

The first Topwell TW-18L to be built in our shop

This photo is the first of the TW-18L taken in our own shop.
March 21 / 05, this model now has a wider front door for
easier access.

a pair of TW-18L machines under assembly at the Topwell factory

The picture above shows one each of the Topwell TW-16L and 18L frames. The machine on the right is being fitted with a Mitsubishi Meldas CNC to be exhibited in a local exhibition in Taiwan. Fanuc, Fagor and Heidenhain CNC systems can be supplied.

It is worth noting that in these shots of the frame before the chip enclosures are fitted that there are only a few pieces of fabrication. 1) the electrical junction box in the lower right corner of the saddle 2) some trip dog brackets 3) the guard around the tool changer Every frame element is cast GA-350 meehanite. No fabrications on this baby. It is a frame that will be rigid enough for the 7 1/2 - 10 Hp spindle drive of the Anilam 6000 CNC system and will easily handle the 1400 IPM rapids and high speed machining The frame in most of the pictures is the TW-18-L. It weighed 2,947 Kg without motors, wiring or the CNC control. We estimate the completed weight will be over 6,900 lb..
Click here to download the TWL Series catalog in pdf format.
Note the very wide casting for the base of this machine and that the inverted ' Y ' design of the column utilises this for added stability. The complete machine is built to take heavier cuts than most " mini-mills " that are fitted with 3 or 5 Hp motors and advertised as having much higher ratings for "intermittent" duty cycles that are revealed as short as 4 minute when you can actually find the small print that specifies this. Our European digital spindle motors are rated for 7 1/2 Hp continuous and 10 Hp for 15 minutes.

Dimensioned picture of the Topwell TW-24-L

June 20 / 05: To the left the new base table and saddle of the TW-24-L. The table is 30" X 18" and sits on a new stronger, wider saddle. The Y axis slideways have been spread 2" wider for additional stability.

The first machines are on the boat and should be here about July 15.

	TWL-18	TWL-24	TWL-40
Travels ( X x Y x Z )
Table Size
Spindle motor
Spindle tooling
Spindle speeds
Rapid traverse rate
Contouring feed rates	3 axis contouring up to 800 IPM and faster ( program compiling depentant ) with auto accel / decel cornering
Automatic Tool Changer

Pull stud for Cat-V tools Pull stud for BT tools	Command RB4M-0001 or equivalent
Spindle nose to table
Designed table load
Ballscrews
Ballscrew thrust bearings
Castings
Approx Weight
Approximate floor space
Accuracy
Repeatability